CWS Sliding & Patio Doors Nationwide | TruePane Windows & Doors

CWS Sliding & Patio Doors: The Doral Owner’s Guide

CWS sliding and patio door parts in Doral typically run $180 to $640 installed depending on whether we’re replacing rollers, a lock set, weatherstripping, or a full handle assembly. We stock the most common CWS-compatible hardware on our trucks, so most Doral jobs are done in a single visit. If your door drags, binds, won’t lock, or whistles during a summer thunderstorm, you’re usually looking at a failed roller assembly or worn weather seal, not a full door replacement.

Call (386) 854-7948

We’re an independent service provider. We are not affiliated with CWS, but we’ve worked on enough of their sliding and patio doors across Doral to know exactly which parts fit which series and which ones fail first in South Florida humidity.

Which CWS Models This Applies To

CWS sliding and patio doors show up in Doral homes built from the late 1990s through the 2010s, most often in the 6800, 7800, and 8900 series. The series number is usually stamped on a label near the door’s top track or on the edge of the sliding panel itself. If that label is gone, which happens more often than not after twenty years of sun, we match the part by measuring the roller housing width and the stile profile.

Here’s where Doral owners get into trouble: CWS changed roller dimensions between the 6800 series and the 7800 series. The 6800 uses a 1-1/4 inch diameter roller with a flat housing, while the 7800 and later series stepped up to a 1-1/2 inch roller with a shouldered housing. They look close enough to confuse at a glance, but the wrong roller makes the door sit low, scrape the track, and eat the new part in six months. We carry both sizes and check the fit before anything goes back on the track.

For OEM versus aftermarket, our position is simple. If CWS’s current OEM part is available and the price difference is under $40, we install OEM. For discontinued series where OEM stock is gone or priced at three times a comparable part, we use American-made aftermarket equivalents from manufacturers we’ve tested in Doral’s salt air. We’ll tell you which one you’re getting and why before we quote it.

Signs Your CWS Sliding & Patio Doors Is Failing

• Door drags or takes shoulder effort to open. Roller bearings are worn or the roller housing has flattened. In Doral, fine sand from pavers and construction dust works into the bearing race and grinds it out years before the roller itself looks bad.
• Door drops when you lift the handle. The roller adjustment screws have backed out or the roller housing has cracked. This is the number one reason CWS doors in Doral get yanked off the track and wind up with bent frames.
• You hear a metallic rasp or grinding on the track. A roller has seized and the door is dragging metal on metal. Every week you wait, the track gets a little more scored, and track repair costs more than the roller ever would have.
• Wind noise or visible daylight at the interlock. The weatherstrip pile has compacted or the interlock alignment has shifted. That’s how Doral’s afternoon rain finds its way to your tile floor.
• Lock won’t throw or the handle flops loose. CWS handle sets use a steel spindle through an aluminum housing. The housing strips first, and once it does, the lock bolt won’t stay engaged. On impact-rated CWS units, a dead lock is also a security problem, not just an annoyance.

Replacement Cost & What’s Included

For CWS sliding and patio door parts in Doral, here’s the line-item reality we quote every week:

• Roller replacement (both panels): $180 to $290 installed, including NewCraft or OEM rollers, track cleaning, and alignment.
• Handle and lock set replacement: $140 to $240 installed, including new mortise lock, interior and exterior handles, and adjustment.
• Weatherstrip replacement (full perimeter): $120 to $210 installed, including interlock pile, bottom sweep, and header seal.
• Full hardware kit (rollers, handle, lock, weatherstrip): $380 to $640 installed, the number depends on series and impact rating.

When you see two numbers side by side on competing quotes, ask what hardware brand is going in. A $9 imported roller and a $28 American-made roller both open a door on day one. They do not open it the same way two years later. Our price includes the part, labor, track cleanup, and adjustment. The Done Right Promise covers the workmanship, and both manufacturer warranty layers, when applicable, are registered in writing before the truck leaves your driveway. No change orders, no surprise line items.

DIY or Call Us?

CWS sliding doors are not high-tension systems like garage door springs. A competent owner with patience can lift a panel for a track cleaning. But the parts themselves, especially the roller replacement on older CWS units, involve removing a heavy glass panel, sometimes impact-rated glass that weighs more than most people expect. If that panel drops or torques, you’re not buying a roller anymore. You’re buying a door.

The place DIY goes wrong on CWS doors is the adjustment. Overshooting the roller height to compensate for a dirty track works for a week, then the door settles hard and cracks the lower rail. We set CWS doors dead level with the panel weight on the rollers, not guessed at while the panel is tilted. If you want to try the handle swap yourself, make sure you know your series before ordering anything online. If you want it done once and done right, call us at (386) 854-7948. The estimate is free, and a live person answers.

FAQs